Application — Autonomous mobile robot (AMR) power
Requirement — This autonomous mobile robot (AMR) power application also required 19V and 12V regulated auxiliary power.
Solution — We integrated 19V and 12V regulated DC-DC converters into a Li-ion 7S pack (DC 25.2V, 51.3Ah).
Result — Three simultaneous outputs — a main DC 25.2V rail at up to 25A (50A peak @ ≤5s) plus regulated 19V and 12V outputs at 10A each — housed in approx. 10kg, complete autonomous mobile robot (AMR) power in a single pack.
If you are considering a custom build to a similar specification, submit a requirements sheet. Our engineer will review it and respond.
Specification
Specifications
| Product Code | DMOP-252LI513-B50-CV |
|---|
General
| Model | DMOP-252LI513-B50-CV |
|---|---|
| Dimension | Approx. L254 x W380 x H75mm (including protrusions) Approx. L230 x W409.6 x H75mm (excluding protrusions) |
| Weight | Approx. 10kg |
Battery ① Electrical specifications
| Battery Type | 7S Li-ion |
|---|---|
| Nominal Voltage | 25.2V (21.0–29.2V) |
| Nominal Capacity | 51.3Ah |
| Energy | 1,292.76Wh |
| Max Discharge Power | Main – DC 25.2V, 630W Converter (regulated) 1 – DC12V, 120W Converter (regulated) 2 – DC19V, 380W |
| Charging Method | CC-CV(Constant Voltage with Limited Current) |
| Standard Charging Condition (0.2C) | 29.2V±1%, 10A, CC-CVEnd Current : 1.026A (0.02C) |
| Max Charging Condition | 29.2V±1%, 25A, CC-CVEnd Current : 1.026A (0.02C) |
| Standard Discharge Current | |
| Max Discharge Current | Main – DC 25.2V, 25A Converter (regulated) 1 – DC12V, 10A Converter (regulated) 2 – DC19V, 10A |
| Instantaneous Discharge Current | Main – 50A @ ≤5s |
| Discharge Cut-off Voltage | 21.0V3.0V per cell |
Battery ② Operation · Safety
| Max Temperature Range | Charging: 0 – +45°C Discharging: -20 – +55°C Storage (recommended): +5 – +30°C |
|---|---|
| Battery Management System | Module configuration: 1P Overcharge cutoff: 4.20–4.25V±25mV per cell Overcharge recovery: 4.00–4.20V±50mV per cell Over-discharge cutoff: 2.50–2.90V±80mV per cell Over-discharge recovery: 2.70–3.30V±100mV per cell Overcurrent cutoff: 135A–160A±25% per module Short-circuit protection: Yes Over-temperature cutoff: Yes Cell balancing: Yes Control method: MOSFET |
| Storage Life | Up to 6 months under no-load conditionsState of charge: SoC 60% Environment: ambient 25°C, humidity ≤70% |
| Cycle Life | ≥60% of nominal capacity after 500 cycles Charge/discharge condition: standard charge, then discharge at the standard discharge current down to the cut-off voltage Environment: ambient 25°C, humidity ≤70% |
Terminals · Control
| Terminal configuration | Positive(+) : 2P(++) Negative(-) : 2P(--) |
|---|---|
| Terminal specification | Rating: 600V, 100A (per pin) Operating temperature range: -40°C – +85°C |
| Terminal fastening and wiring | Bolt: SCREW M6X16 nut Thread: M6*P1.0(B5.0) Recommended tightening torque: 12kgf·cm |
| Charge/discharge switch (ON/OFF) | Option: charge/discharge rocker switch (ON/OFF) |